The default network configuration is:

The GoFlexNet cannot be put into failsafe mode by pressing the button.

It can however be put in failsafe mode using serial console and pressing 'f' and <enter> when prompted during boot-up

The GoFlexNet's only button is not configurable and inevitably performs a hard reset when pressed, the button open the bridge between the positive pole and the power cord.

See Crypto Hardware Acceleration

for serial cable (nokia's DKU-5, CA-42 and etc ttl…), 115200 8n1:

NOTE: The pins to use are the ones "covered up" by the tips of the arrows, i.e. the pins in the row toward the outer edge of the PCB. (for comparison, see here)

for enable 3.5" disks (3 pins sata power to +12V DC):

NOTE: The ellipse in the picture indicates three pins for Serial ATA +12 V. (Multiple pins are used for current (Ampere) considerations, compare https://en.wikipedia.org/wiki/Serial_ATA#Power_connectors.)

NOTE the board is not able to provide enough wattage @5v to drive standard 3.5" hard disks, and even with 'green' disks might not be powerful enough to drive 2 3.5" hd or use a 3.5" hd and a 2.5" at the same time (i.e. Raid1). Using a 'green' 3.5" and a regular 2.5" not at the same time works perfectly for me.

example:

There are no screws - the bottom cover is held by ten plastic snap on clips, three on the sides and two on the edges. To open the case, gently pry all around with a thin screwdriver until it is open.

The serial pins are accessible without further disassembly.

Connect device to Ethernet port. To prevent automatic updates by cloud engines (which will disable ssh access), use a separate switch or disconnect your router from the internet. If the ssh access was disabled by the automatic cloud engine update service, you need to login there and re-activate ssh. On later versions the ssh access is already disabled. The option on the pogoplug site to enable ssh is missing or may be dependent on a public ipv4 and open ssh port on the router.

Find IP address, BE and EF are the last two bytes of the MAC of your device (printed on the bottom of the GoFlexNet)

root@host ~ # ifconfig eth0 169.254.1.0 
root@host ~ # nmap -e eth0 -sP $(printf "169.254.%d.%d" 0xbe 0xef)

Connect to IP address via ssh (root / stxadmin) to see if it works.

Login to the original firmware via SSH (enable it first in popoplug site) or Serial cable (nokia's CA-52, DKU-5 and etc ttl…). Plug the flash drive (FAT32) to USB port in Seagate GoFlex Net, then:

mkdir /tmp/backup
mount /dev/sda1 /tmp/backup
cd /tmp/backup
wget http://download.doozan.com/uboot/nanddump
chmod +x nanddump
./nanddump -nof uboot-mtd0-dump /dev/mtd0
./nanddump -nof uboot-original -s 0 -l 0x80000 /dev/mtd0
./nanddump -nof uImage-mtd1-dump /dev/mtd1
./nanddump -nof rootfs-mtd2-dump /dev/mtd2
umount /dev/sda1

To create an image of mtd0, you need to dump the nand without ecc. using "dd if=/dev/mtd0 of=mtd0.DOESNOTWORK" will automatically do ecc for you and will result in a corrupt image.

#set goflex net ip
setenv ipaddr '192.168.1.1'
#set tftp-server ip
setenv serverip '192.168.1.2'

#original uImage (backuped before)
tftpboot 0x800000 uImage-mtd1-dump
nand erase 0x100000 0x400000
nand write.e 0x800000 0x100000 0x400000

#original rootfs (backuped before)
tftpboot 0x800000 rootfs-mtd2-dump
nand erase 0x500000 0x2000000
nand write.e 0x800000 0x500000 0x2000000

resetenv
reset

Hit any key to stop autoboot:  0

setenv bootcmd 'nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000'

#change value to your device
setenv ethaddr '00:10:75:26:3D:9F'
setenv cesvcid '5RFAJDGYNLPLDUHN4BWUWC3EKJ'
setenv ceserialno 'NA1Y0EG1'
setenv ceboardver 'DISCOVERY:0.1'
saveenv

reset

Prerequisites

• hookup a (USB-)serial to the goflexnet box and get it running (e.g. minicom)
• connect the Goflexnet and your computer to a router (or directly and counfigure your computer with static IP 192.168.2.1)

Files to download

• uboot (via doozan forum)
• openwrt-15.05.1-kirkwood-goflexnet-uImage
• openwrt-15.05.1-kirkwood-goflexnet-rootfs.ubifs

Todo

• get data partition working
• file ticket because trunk kernel won't boot

Extract the uboot

tar -xvf uboot.2016.05-tld-1.goflexnet.bodhi.tar

Start a tftp server in that folder

sudo dnsmasq -p0 --enable-tftp --tftp-root=`pwd` -d --user=`whoami`

Hit any key to stop autoboot in the uboot and set goflexnet ip, tftp-server ip, goflexnet mac:

setenv ipaddr '192.168.1.1'
setenv serverip '192.168.1.2'
setenv ethaddr 'yourmac' <<- it is written on the bottom of your goflexnet box

download from tftp-server file uboot.2016.05-tld-1.goflexnet.mtd0.kwb to RAM start offset 0x6400000

tftp 0x6400000 uboot.2016.05-tld-1.goflexnet.mtd0.kwb

Bytes transferred = 524288 (80000 hex) ← this number is needed for nand write erase nand start from 0 size 0x100000

nand erase 0x0 0x100000

write nand from RAM start offset 0x6400000 to nand start 0x0 size 0x80000

nand write.e 0x6400000 0x0 0x80000

download from tftp-server file openwrt-15.05.1-kirkwood-goflexnet-uImage to RAM start offset 0x6400000

tftp 0x6400000 openwrt-15.05.1-kirkwood-goflexnet-uImage

Bytes transferred = 1740617 (1a8f49 hex) ← this number is needed for nand write erase nand start from 0x100000 size 0x400000

nand erase 0x100000 0x400000

write nand from RAM start offset 0x6400000 to nand start 0x100000 size 1a8f49

nand write.e 0x6400000 0x100000 1a8f49

erase nand rootfs (start 0x500000 size 0x2000000)

nand erase.part rootfs

NAND erase.part: device 0 offset 0x500000, size 0x2000000 Erasing at 0x24e0000 – 100% complete. OK

select partition rootfs

ubi part rootfs

ubi0: attaching mtd1
ubi0: scanning is finished
ubi0: empty MTD device detected
ubi0: attached mtd1 (name "mtd=2", size 32 MiB)
ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512
ubi0: VID header offset: 512 (aligned 512), data offset: 2048
ubi0: good PEBs: 256, bad PEBs: 0, corrupted PEBs: 0
ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 0 
ubi0: available PEBs: 212, total reserved PEBs: 44, PEBs reserved for bad PEB h0

create ubi fs?

ubi create rootfs

No size specified → Using max size (27353088) Creating dynamic volume rootfs of size 27353088

download from tftp-server openwrt-15.05.1-kirkwood-goflexnet-rootfs.ubifs to RAM start offset 0x6400000

tftp 0x6400000 openwrt-15.05.1-kirkwood-goflexnet-rootfs.ubifs

Bytes transferred = 4644864 (46e000 hex) ← this number is needed for nand write

write nand from RAM start offset 0x6400000 to nand start 0x500000 size 4c0000

ubi write 0x6400000 rootfs 46e000

4644864 bytes written to volume rootfs

reboot

reset

Hit any key to stop autoboot! and set your mac-address from bottom side of the box (if you don't do this - ethernet wont work) and set other openwrt's environment

setenv baudrate '115200'
setenv bootcmd '${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; ${x_bootcmd_usb}; bootm 0x6400000;'
setenv bootdelay '3'
setenv ethact 'egiga0'
setenv ethaddr 'yourmacaddress'
setenv ipaddr '192.168.1.1'
setenv serverip '192.168.1.2'
setenv stderr 'serial'
setenv stdin 'serial'
setenv stdout 'serial'
setenv x_bootargs 'console=ttyS0,115200 mtdparts=orion_nand:1M(u-boot),4M@1M(kernel),32M@5M(rootfs),-(data) rw'
setenv x_bootargs_root 'ubi.mtd=2  rootfstype=ubifs'
setenv x_bootcmd_kernel 'nand read 0x6400000 0x100000 0x400000'
setenv x_bootcmd_usb 'usb start'
setenv machid c11
saveenv
reset

we did it:

U-Boot 2016.05-tld-1 (Jun 12 2016 - 13:27:19 -0700)
Seagate GoFlex Net

SoC:   Kirkwood 88F6281_A1
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot:  0 

NAND read: device 0 offset 0x100000, size 0x400000
 4194304 bytes read: OK
starting USB...
USB0:   USB EHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
## Booting kernel from Legacy Image at 06400000 ...
   Image Name:   ARM OpenWrt Linux-3.18.23
   Created:      2016-02-02  12:35:05 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1740553 Bytes = 1.7 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
Using machid 0xc11 from environment

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.18.23 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r47269) ) #1 Sun Jan 31 11:40:01 CET 2016
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005397f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine model: Seagate GoFlex Net
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:1M(u-boot),4M@1M(kernel),32M@5M(rootfs) rw,219M@37M(data) ubi.mtd=2 rootfstype=ubifs
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 124916K/131072K available (3466K kernel code, 151K rwdata, 964K rodata, 136K init, 191K bss, 6156K reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xffe00000   (2048 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff000000   ( 872 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc045bd4c   (4432 kB)
[    0.000000]       .init : 0xc045c000 - 0xc047e000   ( 136 kB)
[    0.000000]       .data : 0xc047e000 - 0xc04a3e04   ( 152 kB)
[    0.000000]        .bss : 0xc04a3e04 - 0xc04d3b44   ( 192 kB)
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000015] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474836475ns
[    0.000160] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[    0.090095] pid_max: default: 32768 minimum: 301
[    0.090239] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090257] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.090729] CPU: Testing write buffer coherency: ok
[    0.091063] Setting up static identity map for 0x108d8 - 0x10914
[    0.091358] mvebu-soc-id: MVEBU SoC ID=0x6281, Rev=0x3
[    0.093121] pinctrl core: initialized pinctrl subsystem
[    0.093527] regulator-dummy: no parameters
[    0.097479] NET: Registered protocol family 16
[    0.097879] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.098738] cpuidle: using governor ladder
[    0.099098] Feroceon L2: Enabling L2
[    0.099141] Feroceon L2: Cache support initialised.
[    0.099433] [Firmware Info]: /ocp@f1000000/ethernet-controller@72000/ethernet0-port@0: local-mac-address is not set
[    0.107168] platform regulators:regulator@1: Driver reg-fixed-voltage requests probe deferral
[    0.107555] SCSI subsystem initialized
[    0.107907] usbcore: registered new interface driver usbfs
[    0.107985] usbcore: registered new interface driver hub
[    0.108054] usbcore: registered new device driver usb
[    0.109001] Switched to clocksource orion_clocksource
[    0.110102] NET: Registered protocol family 2
[    0.110807] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.110831] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.110850] TCP: Hash tables configured (established 1024 bind 1024)
[    0.110909] TCP: reno registered
[    0.110922] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.110942] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.111119] NET: Registered protocol family 1
[    0.111965] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.112923] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.112943] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.113190] msgmni has been set to 243
[    0.114026] io scheduler noop registered
[    0.114045] io scheduler deadline registered (default)
[    0.115157] kirkwood-pinctrl f1010000.pin-controller: registered pinctrl driver
[    0.115719] irq: Cannot allocate irq_descs @ IRQ33, assuming pre-allocated
[    0.116042] irq: Cannot allocate irq_descs @ IRQ65, assuming pre-allocated
[    0.148632] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[    0.151718] console [ttyS0] disabled
[    0.151790] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 26, base_baud = 12500000) is a 16550A
[    0.548112] console [ttyS0] enabled
[    0.552993] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[    0.559401] nand: Micron MT29F2G08AAD
[    0.563082] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    0.568781] Scanning device for bad blocks
[    0.790299] 3 cmdlinepart partitions found on MTD device orion_nand
[    0.796594] Creating 3 MTD partitions on "orion_nand":
[    0.801782] 0x000000000000-0x000000100000 : "u-boot"
[    0.807521] 0x000000100000-0x000000500000 : "kernel"
[    0.813225] 0x000000500000-0x000002500000 : "rootfs"
[    0.818886] mtd: device 2 (rootfs) set to be root filesystem
[    0.824691] mtdsplit: no squashfs found in "rootfs"
[    0.829695] mtdsplit: no squashfs found in "orion_nand"
[    0.835440] libphy: orion_mdio_bus: probed
[    0.888802] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    0.897017] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:10:75:xx:xx:xx
[    0.905841] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.912418] ehci-pci: EHCI PCI platform driver
[    0.916946] ehci-platform: EHCI generic platform driver
[    0.922333] ehci-orion: EHCI orion driver
[    0.926507] orion-ehci f1050000.ehci: EHCI Host Controller
[    0.932065] orion-ehci f1050000.ehci: new USB bus registered, assigned bus number 1
[    0.939890] orion-ehci f1050000.ehci: irq 29, io mem 0xf1050000
[    0.959021] orion-ehci f1050000.ehci: USB 2.0 started, EHCI 1.00
[    0.965677] hub 1-0:1.0: USB hub found
[    0.969502] hub 1-0:1.0: 1 port detected
[    0.974015] usbcore: registered new interface driver usb-storage
[    0.982008] TCP: cubic registered
[    0.985345] NET: Registered protocol family 17
[    0.989908] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.002617] Bridge firewalling registered
[    1.006761] 8021q: 802.1Q VLAN Support v1.8
[    1.012286] USB Power: 5000 mV 
[    1.015668] UBI: attaching mtd2 to ubi0
[    1.078150] UBI: scanning is finished
[    1.093646] UBI: attached mtd2 (name "rootfs", size 32 MiB) to ubi0
[    1.099973] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes
[    1.106791] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 512
[    1.113440] UBI: VID header offset: 512 (aligned 512), data offset: 2048
[    1.120179] UBI: good PEBs: 256, bad PEBs: 0, corrupted PEBs: 0
[    1.126123] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
[    1.133295] UBI: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
[    1.141604] UBI: available PEBs: 0, total reserved PEBs: 256, PEBs reserved for bad PEB handling: 40
[    1.150967] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.158325] UBI: background thread "ubi_bgt0d" started, PID 775
[    1.195356] UBIFS: background thread "ubifs_bgt0_0" started, PID 780
[    1.228709] UBIFS: start fixing up free space
[    1.674642] UBIFS: free space fixup complete
[    1.721114] UBIFS: mounted UBI device 0, volume 0, name "rootfs"
[    1.727152] UBIFS: LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    1.736357] UBIFS: FS size: 25933824 bytes (24 MiB, 201 LEBs), journal size 9033728 bytes (8 MiB, 71 LEBs)
[    1.746066] UBIFS: reserved for root: 0 bytes (0 KiB)
[    1.751154] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 910BF25D-BEAF-40CE-B84A-3220E8E2EAC5, small LPT model
[    1.762444] VFS: Mounted root (ubifs filesystem) on device 0:10.
[    1.768869] Freeing unused kernel memory: 136K (c045c000 - c047e000)
[    1.908005] init: Console is alive
[    2.037961] sata_mv f1080000.sata: slots 32 ports 2
[    2.045498] scsi host0: sata_mv
[    2.049289] scsi host1: sata_mv
[    2.052665] ata1: SATA max UDMA/133 irq 32
[    2.056785] ata2: SATA max UDMA/133 irq 32
[    2.409025] ata1: SATA link down (SStatus 0 SControl F300)
[    2.759019] ata2: SATA link down (SStatus 0 SControl F300)
[    2.913139] init: - preinit -
[    2.985670] random: procd urandom read with 4 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    6.087058] mount_root: mounting /dev/root
[    6.103452] procd: - early -
[    7.185643] procd: - ubus -
[    8.192456] procd: - init -
Please press Enter to activate this console.
[   10.407705] NET: Registered protocol family 10
[   10.433489] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   10.457405] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.492793] nf_conntrack version 0.5.0 (1953 buckets, 7812 max)
[   10.589545] xt_time: kernel timezone is -0000
[   10.613902] PPP generic driver version 2.4.2
[   10.636613] NET: Registered protocol family 24
[   13.588581] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled
[   13.598413] mv643xx_eth_port mv643xx_eth_port.0 eth0: link down
[   13.605554] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   34.611312] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled
[   34.621154] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   78.189036] random: nonblocking pool is initialized

openwrt CC

BusyBox v1.23.2 (2016-01-02 02:33:25 CET) built-in shell (ash)

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 CHAOS CALMER (15.05.1, r48532)
 -----------------------------------------------------
  * 1 1/2 oz Gin            Shake with a glassful
  * 1/4 oz Triple Sec       of broken ice and pour
  * 3/4 oz Lime Juice       unstrained into a goblet.
  * 1 1/2 oz Orange Juice
  * 1 tsp. Grenadine Syrup
 -----------------------------------------------------
root@OpenWrt:/#

Files needed: http://dl.dropbox.com/u/1015928/Kirkwood/uboot/newer-uboots-nonEFI_GPT-TESTED/uboot.mtd0.kwb-2011.12-goflexnet-L2Coff-IDEpatched.tar.gz (Mirror: http://www.wit.dk/temp/SeagateGoFlexNet/uboot.mtd0.kwb-2011.12-goflexnet-L2Coff-IDEpatched.tar.gz)

(untar - this is uboot with working sata!)

https://downloads.openwrt.org/snapshots/trunk/kirkwood/generic/openwrt-kirkwood-uImage

https://downloads.openwrt.org/snapshots/trunk/kirkwood/generic/openwrt-kirkwood-generic-jffs2-nand-2048-128k.img

Hit any key to stop autoboot in the uboot and set goflexnet ip, tftp-server ip, goflexnet mac:

setenv ipaddr '192.168.1.1'
setenv serverip '192.168.1.2'
setenv ethaddr '00:10:75:26:28:7D'

download from tftp-server file uboot.mtd0.kwb-2011.12-goflexnet-L2Coff-IDEpatched to RAM start offset 0x6400000

tftp 0x6400000 uboot.mtd0.kwb-2011.12-goflexnet-L2Coff-IDEpatched

Bytes transferred = 524288 (80000 hex) ← this number is needed for nand write

erase nand start from 0 size 0x100000

nand erase 0x0 0x100000

write nand from RAM start offset 0x6400000 to nand start 0x0 size 0x80000

nand write.e 0x6400000 0x0 0x80000

download from tftp-server file openwrt-kirkwood-uImage to RAM start offset 0x6400000

tftp 0x6400000 openwrt-kirkwood-uImage

Bytes transferred = 1266344 (1352a8 hex) ← this number is needed for nand write

erase nand start from 0x200000 size 0x300000

nand erase 0x200000 0x300000

write nand from RAM start offset 0x6400000 to nand start 0x200000 size 0x1352a8

nand write.e 0x6400000 0x200000 0x1352a8

download from tftp-server file openwrt-kirkwood–jffs2-nand-2048-128k.img to RAM start offset 0x6400000

tftp 0x6400000 openwrt-kirkwood--jffs2-nand-2048-128k.img

Bytes transferred = 1837056 (1c0800 hex) ← this number is needed for nand write

erase nand start from 0x500000 size 0xfb00000

nand erase 0x500000 0xfb00000

write nand from RAM start offset 0x6400000 to nand start 0x500000 size 0x1c0800

nand write.e 0x6400000 0x500000 0x1c0800

reboot device

reset

Hit any key to stop autoboot! and set your mac-address from bottom side of the box (if you don't do this - ethernet wont work) and set other openwrt's environment

setenv baudrate '115200'
setenv bootcmd '${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; ${x_bootcmd_usb}; bootm 0x6400000;'
setenv bootdelay '3'
setenv ethact 'egiga0'
setenv ethaddr '00:10:75:26:28:7D'
setenv ipaddr '192.168.1.1'
setenv serverip '192.168.1.2'
setenv stderr 'serial'
setenv stdin 'serial'
setenv stdout 'serial'
setenv x_bootargs 'console=ttyS0,115200 mtdparts=orion_nand:1M(u-boot),1M@1M(second_stage_u-boot),3M@2M(kernel),251M@5M(rootfs) rw'
setenv x_bootargs_root 'root=/dev/mtdblock3 rw rootfstype=jffs2'
setenv x_bootcmd_kernel 'nand read 0x6400000 0x200000 0x300000'
setenv x_bootcmd_usb 'usb start'
setenv machid c11
saveenv
reset

Voilà, we did it! :)

U-Boot 2011.12 (Apr 18 2012 - 23:08:20)
Seagate GoFlexNet

SoC:   Kirkwood 88F6281_A0
DRAM:  128 MiB
WARNING: Caches not enabled
NAND:  256 MiB
In:    serial
Out:   serial
Err:   serial
Net:   egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x200000, size 0x300000
 3145728 bytes read: OK
(Re)start USB...
USB:   Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
       scanning bus for storage devices... 0 Storage Device(s) found
## Booting kernel from Legacy Image at 06400000 ...
   Image Name:   Linux-3.3.8
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1266192 Bytes = 1.2 MiB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0
[    0.000000] Linux version 3.3.8 (openwrt@OpenWRT) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38047) ) #1 Thu Sep 19 01:30:05 MST 2013
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: Marvell eSATA SheevaPlug Reference Board
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: console=ttyS0,115200 mtdparts=orion_nand:1M(u-boot),1M@1M(second_stage_u-boot),3M@2M(kernel),251M@5M(rootfs) rw root=/dev/mtdblock3 rw rootfstype=jffs2
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 128MB = 128MB total
[    0.000000] Memory: 126284k/126284k available, 4788k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff000000   ( 872 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0324000   (3184 kB)
[    0.000000]       .init : 0xc0324000 - 0xc0342000   ( 120 kB)
[    0.000000]       .data : 0xc0342000 - 0xc035fb20   ( 119 kB)
[    0.000000]        .bss : 0xc035fb44 - 0xc0389a90   ( 168 kB)
[    0.000000] NR_IRQS:114
[    0.000000] gpiochip_add: registered GPIOs 0 to 31 on device: orion_gpio0
[    0.000000] gpiochip_add: registered GPIOs 32 to 49 on device: orion_gpio1
[    0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, wraps every 21474ms
[   15.378138] Calibrating delay loop... 1191.11 BogoMIPS (lpj=5955584)
[   15.468126] pid_max: default: 32768 minimum: 301
[   15.468266] Mount-cache hash table entries: 512
[   15.468584] CPU: Testing write buffer coherency: ok
[   15.468840] Setting up static identity map for 0x2757e8 - 0x275824
[   15.470513] NET: Registered protocol family 16
[   15.472748] Kirkwood: MV88F6281-A0, TCLK=200000000.
[   15.472764] Feroceon L2: Enabling L2
[   15.472801] Feroceon L2: Cache support initialised.
[   15.480475] bio: create slab <bio-0> at 0
[   15.481375] SCSI subsystem initialized
[   15.481930] usbcore: registered new interface driver usbfs
[   15.482067] usbcore: registered new interface driver hub
[   15.482226] usbcore: registered new device driver usb
[   15.483324] Switching to clocksource orion_clocksource
[   15.484874] NET: Registered protocol family 2
[   15.485020] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[   15.485321] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[   15.485420] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[   15.485474] TCP: Hash tables configured (established 4096 bind 4096)
[   15.485484] TCP reno registered
[   15.485494] UDP hash table entries: 256 (order: 0, 4096 bytes)
[   15.485516] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[   15.485690] NET: Registered protocol family 1
[   15.487175] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[   15.487189] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[   15.487525] msgmni has been set to 246
[   15.487555] io scheduler noop registered
[   15.487563] io scheduler deadline registered (default)
[   15.554884] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[   15.577632] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[   15.918534] console [ttyS0] enabled
[   15.923472] ONFI flash detected
[   15.926716] ONFI param page 0 valid
[   15.930224] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08AAD)
[   15.937929] Scanning device for bad blocks
[   16.094164] 4 cmdlinepart partitions found on MTD device orion_nand
[   16.100459] Creating 4 MTD partitions on "orion_nand":
[   16.105637] 0x000000000000-0x000000100000 : "u-boot"
[   16.111557] 0x000000100000-0x000000200000 : "second_stage_u-boot"
[   16.118542] 0x000000200000-0x000000500000 : "kernel"
[   16.124386] 0x000000500000-0x000010000000 : "rootfs"
[   16.130502] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[   16.137474] mv643xx_eth smi: probed
[   16.142824] mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address 00:10:75:26:28:7d
[   16.151794] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   16.158406] orion-ehci orion-ehci.0: Marvell Orion EHCI
[   16.163725] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[   16.193367] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[   16.213355] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   16.219848] hub 1-0:1.0: USB hub found
[   16.223640] hub 1-0:1.0: 1 port detected
[   16.228077] Initializing USB Mass Storage driver...
[   16.233153] usbcore: registered new interface driver usb-storage
[   16.239200] USB Mass Storage support registered.
[   16.244122] cpuidle: using governor ladder
[   16.249582] mmc0: mvsdio driver initialized, using GPIO 47 for card detection
[   16.256984] leds-gpio: probe of leds-gpio failed with error -22
[   16.263254] TCP cubic registered
[   16.266519] NET: Registered protocol family 17
[   16.271047] Bridge firewalling registered
[   16.275254] 8021q: 802.1Q VLAN Support v1.8
[   16.279588] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[   17.972758] JFFS2 notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   17.991751] VFS: Mounted root (jffs2 filesystem) on device 31:3.
[   17.998179] Freeing init memory: 120K
procd: Console is alive
[   20.599310] Uniform Multi-Platform E-IDE driver
[   20.623458] sata_mv sata_mv.0: slots 32 ports 2
[   20.629741] scsi0 : sata_mv
[   20.632984] scsi1 : sata_mv
[   20.636119] ata1: SATA max UDMA/133 irq 21
[   20.640234] ata2: SATA max UDMA/133 irq 21
[   20.993364] ata1: SATA link down (SStatus 0 SControl F300)
[   21.503369] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl F300)
[   21.883398] ata2.00: ATA-6: TOSHIBA MK1032GSX, AS021G, max UDMA/100
[   21.889697] ata2.00: 195371568 sectors, multi 16: LBA48 NCQ (depth 31/32)
[   21.953398] ata2.00: configured for UDMA/100
[   21.957957] scsi 1:0:0:0: Direct-Access     ATA      TOSHIBA MK1032GS AS02 PQ: 0 ANSI: 5
[   21.967355] sd 1:0:0:0: [sda] 195371568 512-byte logical blocks: (100 GB/93.1 GiB)
[   21.975267] sd 1:0:0:0: [sda] Write Protect is off
[   21.980167] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   22.030739]  sda: sda1
[   22.034046] sd 1:0:0:0: [sda] Attached SCSI disk
[   22.045058] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[   22.052996] uhci_hcd: USB Universal Host Controller Interface driver
kmod: ran 28 iterations
procd: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
mount_root: mounting /dev/root
procd: - early -
procd: - init -
Please press Enter to activate this console.
[   28.126425] NET: Registered protocol family 10
[   28.193973] aoe: AoE v47 initialised.
[   28.253711] RPC: Registered named UNIX socket transport module.
[   28.259662] RPC: Registered udp transport module.
[   28.264413] RPC: Registered tcp transport module.
[   28.269131] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   28.287417] NTFS driver 2.1.30 [Flags: R/O MODULE].
[   28.315502] tun: Universal TUN/TAP device driver, 1.6
[   28.320580] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   28.387485] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   28.411442] nf_conntrack version 0.5.0 (1975 buckets, 7900 max)
[   28.437469] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   28.513508] sd 1:0:0:0: Attached scsi generic sg0 type 0
[   28.543385] u32 classifier
[   28.546104]     input device check on
[   28.549775]     Actions configured
[   28.564556] Mirror/redirect action on
[   28.624722] netem: version 1.3
[   28.663524] fuse init (API version 7.18)
[   28.680251] ip_tables: (C) 2000-2006 Netfilter Core Team
[   28.726045] usbcore: registered new interface driver usblp
[   28.823510] xt_time: kernel timezone is -0000
[   28.851447] PPP generic driver version 2.4.2
[   28.861255] NET: Registered protocol family 24
[   33.545126] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   36.346205] mv643xx_eth_port mv643xx_eth_port.0: eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[   36.356457] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
procd: - init complete -



BusyBox v1.19.4 (2013-09-19 01:21:59 MST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 BARRIER BREAKER (Bleeding Edge, r38047)
 -----------------------------------------------------
  * 1/2 oz Galliano         Pour all ingredients into
  * 4 oz cold Coffee        an irish coffee mug filled
  * 1 1/2 oz Dark Rum       with crushed ice. Stir.
  * 2 tsp. Creme de Cacao
 -----------------------------------------------------
root@OpenWrt:/# df -h
Filesystem                Size      Used Available Use% Mounted on
rootfs                  251.0M     22.5M    228.5M   9% /
/dev/root               251.0M     22.5M    228.5M   9% /
tmpfs                    61.7M    236.0K     61.5M   0% /tmp
tmpfs                   512.0K         0    512.0K   0% /dev
/dev/sda1                93.2G     88.6M     93.1G   0% /tmp/run/mountd/sda1
root@OpenWrt:/#

all files are here: redstone_v63

Checksums:

ce_kernel_redstone_v63.img: c31ca085da5999651384cf4bb9978692

ce_ramdisk_v2.0b.img.gz: 80787eea2389a1fe96ffc6715ec65d4c

setenv ipaddr '192.168.1.1'
setenv serverip '192.168.1.2'
nand erase 0x100000 0x400000
tftp 0x800000 ce_kernel_redstone_v63.img
nand write.e 0x800000 0x100000 0x1e30f0
tftp 0x1000000 ce_ramdisk_v2.0b.img.gz
setenv bootargs $(console) root=/dev/mtdblock2 initrd=0x1000000,0xb39a59
bootm 0x800000

Unlike the dockstar, the goflexnet has a newer bootrom which supports serial boot. [http://forum.doozan.com/read.php?3,7852,7852]

wget ftp://ftp.denx.de/pub/u-boot/u-boot-2013.10.tar.bz2
tar jxf u-boot-2013.10.tar.bz2
cd u-boot-2013.10/tools/
gcc -o kwboot kwboot.c
./kwboot -b /tmp/openwrt-kirkwood-goflexhome-u-boot.kwb -t -p -B 115200 /dev/ttyUSB0

Now the uboot is loaded into ram and executed. You have to flash u-boot into nand. See below how to flash it.

information from console of BusPirate (SeeedStudio) "HiZ>i" - Bus Pirate v3.5 Firmware v6.1 r1676 Bootloader v4.4 in bash of Cygwin

git clone git://git.code.sf.net/p/openocd/code
cd code
./bootstrap
./configure --enable-maintainer-mode --disable-werror --disable-at91rm9200 --enable-buspirate
make && make install && make clean

put buspirate.cfg to /usr/local/share/openocd/scripts/interface/
put dockstar.cfg to /usr/local/share/openocd/scripts/board/
put uboot.mtd0.goflexnet.original.kwb from http://download.doozan.com/uboot/files/uboot/uboot.mtd0.goflexnet.original.kwb to /usr/local/share/openocd/scripts/

cd /usr/local/share/openocd/scripts

(Seeed Studio BusPirate - GoFlex.net)  (GoFlex.net - Seeed Studio BusPirate)
(            nc         -   1  nc   )  ( 10  GND   -    serial cable GND   )
(     6  blue   (aux)   -   2  IN   )  (  9  RxD   -    serial cable TxD   )
(     8  gray   (mosi)  -   3  TDI  )  (  8  TxD   -    serial cable RxD   )
(     9  white  (cs)    -   4  TMS  )  (  7  CN    -           nc          )
(     7  purple (clk)   -   5  TCK  )  (  6  DOT   -    10  black (miso)   )
power on goflex.net, serial, buspirate

openocd.exe -f board/dockstar.cfg

in telnet 127.0.0.1 4444:
init
type 'halt' - press reset - press enter - release reset

(repeat while not see this:
target state: halted
target halted in ARM state due to debug-request, current fashion: Supervisor
CPSR: 0x000000d3 pc: 0xffff0000
MMU: disabled, D-Cache: disabled, I-Cache: disabled
if you not see this - you can try command 'soft_reset_halt')

dockstar_init

(here are two options to choose from)
------
load_image uboot.mtd0.goflexnet.original.kwb 0x800000
(wait ~214 sec)
resume 0x800200
------
or you can erease nand and native write to nand:
------
nand probe 0
nand erase 0 0x0 0xa0000
nand write 0 uboot.mtd0.goflexnet.original.kwb 0 oob_softecc_kw
(wait ~569 sec)
(then poweroff goflexnet & buspirate, wait 5 secs adns poweron goflexnet)
------


in serial console:
Hit any key to stop autoboot:  0
nand erase
nand write.e 0x800000 0x0 0x80000
reset

buspirate.cfg

interface buspirate
buspirate_port /dev/ttyS15
buspirate_speed fast #normal or fast
buspirate_vreg 0
buspirate_mode open-drain
buspirate_pullup 0
reset_config srst_only

dockstar.cfg

# Marvell SheevaPlug

# I'm using a wiggler compatible cable
source [find interface/buspirate.cfg]
source [find target/feroceon.cfg]
jtag_khz 500
jtag_nsrst_delay 500

$_TARGETNAME configure \
	-work-area-phys 0x100000 \
	-work-area-size 65536 \
	-work-area-backup 0

# Disabled for the dockstar	
#arm7_9 dcc_downloads enable

# this assumes the hardware default peripherals location before u-Boot moves it
set _FLASHNAME $_CHIPNAME.flash
nand device $_FLASHNAME orion 0 0xd8000000

proc dockstar_init { } {

	# We need to assert DBGRQ while holding nSRST down.
	# However DBGACK will be set only when nSRST is released.
	# Furthermore, the JTAG interface doesn't respond at all when
	# the CPU is in the WFI (wait for interrupts) state, so it is
	# possible that initial tap examination failed.  So let's
	# re-examine the target again here when nSRST is asserted which
	# should then succeed.
	jtag_reset 0 1
	feroceon.cpu arp_examine
	halt 0
	jtag_reset 0 0
	wait_halt

	arm mcr 15 0 0 1 0 0x00052078

	mww 0xD0001400 0x43000C30
	mww 0xD0001404 0x39543000 
	mww 0xD0001408 0x22125451 
	mww 0xD000140C 0x00000833 
	mww 0xD0001410 0x000000CC
	mww 0xD0001414 0x00000000 
	mww 0xD0001418 0x00000000
	mww 0xD000141C 0x00000C52 
	mww 0xD0001420 0x00000042 
	mww 0xD0001424 0x0000F17F 
	mww 0xD0001428 0x00085520 
	mww 0xD000147c 0x00008552 

	# 1st bank is 128 MB
	mww 0xD0001504 0x07FFFFF1 
	# 2nd bank of DRAM is not used
	mww 0xD0001508 0x00000000 
	mww 0xD000150C 0x00000000
	# Commented the 3 following	lines
	#mww 0xD0001504 0x0FFFFFF1 
	#mww 0xD0001508 0x10000000 
	#mww 0xD000150C 0x0FFFFFF5 
	mww 0xD0001514 0x00000000
	mww 0xD000151C 0x00000000
	mww 0xD0001494 0x003C0000 
	mww 0xD0001498 0x00000000
	mww 0xD000149C 0x0000F80F 
	mww 0xD0001480 0x00000001 
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000
	mww 0xD0020204 0x00000000

	mww 0xD0010000 0x01111111 
	mww 0xD0010004 0x11113322 
	mww 0xD0010008 0x00001111

	mww 0xD0010418 0x003E07CF
	mww 0xD001041C 0x000F0F0F
	mww 0xD0010470 0x01C7D943

}

proc sheevaplug_reflash_uboot { } {

	# reflash the u-Boot binary and reboot into it
	sheevaplug_init
	nand probe 0
	nand erase 0 0x0 0xa0000
	nand write 0 uboot.bin 0 oob_softecc_kw
	resume

}

proc sheevaplug_reflash_uboot_env { } {

	# reflash the u-Boot environment variables area
	sheevaplug_init
	nand probe 0
	nand erase 0 0xa0000 0x40000
	nand write 0 uboot-env.bin 0xa0000 oob_softecc_kw
	resume

}

proc sheevaplug_load_uboot { } {

	# load u-Boot into RAM and execute it
	sheevaplug_init
	#load_image uboot.elf
	#verify_image uboot.elf
	load_image u-boot
	verify_image u-boot
	resume 0x00600000

}

proc dockstar_reset_cpu { } {

#	System and User mode registers
#		  r0: 00000000       r1: 00000000       r2: 00000000       r3: 00000000
#		  r4: 00000000       r5: 00000000       r6: 00000000       r7: 00000000
#		  r8: 00000000       r9: 00000000      r10: 00000000      r11: 00000000
#		 r12: 00000000   sp_usr: 7dddee86   lr_usr: dffebe46       pc: ffff0a42
#		cpsr: 400000f3

	reg r1 0
	reg r2 0
	reg r3 0
	reg r4 0
	reg r5 0
	reg r6 0
	reg r7 0
	reg r8 0
	reg r9 0
	reg r10 0
	reg r11 0
	reg r12 0
	reg sp_usr 0
	reg lr_usr 0
	reg pc 0
	# Set the CPU in Supervisor mode
	reg cpsr 0x13

#	FIQ mode shadow registers
#	  r8_fiq: fbcfff64   r9_fiq: d7dfafd6  r10_fiq: 1fff6d2e  r11_fiq: 1db65df4
#	 r12_fiq: ff5a6de4   sp_fiq: 745fe7d5   lr_fiq: 89f7ae3e spsr_fiq: 00000000

	reg r8_fiq 0
	reg r9_fiq 0
	reg r10_fiq 0
	reg r11_fiq 0
	reg r12_fiq 0
	reg sp_fiq 0
	reg lr_fiq 0
	reg spsr_fiq 0

#	Supervisor mode shadow registers
#	  sp_svc: fffeff84   lr_svc: ffff0a43 spsr_svc: 00000000

	reg sp_svc 0
	reg lr_svc 0
	reg spsr_svc 0

#	Abort mode shadow registers
#	  sp_abt: 51fe66f7   lr_abt: d7abaef7 spsr_abt: 00000000

	reg sp_abt 0
	reg lr_abt 0
	reg spsr_abt 0

#	IRQ mode shadow registers
#	  sp_irq: 7fdb4ed5   lr_irq: 6d41122e spsr_irq: 00000000

	reg sp_irq 0
	reg lr_irq 0
	reg spsr_irq 0
	
#	Undefined instruction mode shadow registers
#	  sp_und: 75ffef7e   lr_und: d75b6cd1 spsr_und: 00000000

	reg sp_und 0
	reg lr_und 0
	reg spsr_und 0
	
}

baudrate=115200
loads_echo=0
rootpath=/mnt/ARM_FS/
run_diag=yes
console=console=ttyS0,115200
CASset=min
MALLOC_len=1
ethprime=egiga0
bootargs_root=root=/dev/mtdblock2 ro
ethmtu=1500
usb0Mode=host
nandEcc=1bit
bootargs=console=ttyS0,115200 root=/dev/mtdblock2 ro
ethaddr=00:10:75:26:3D:9F
cesvcid=5RFAJDGYNLPLDUHN4BWUWC3EKJ
ceserialno=NA1Y0EG1
ceboardver=DISCOVERY:0.1
ethact=egiga0
filesize=1b60000
fileaddr=1000000
netmask=255.255.0.0
ipaddr=192.168.1.1
serverip=192.168.1.2
bootcmd=nand read.e 0x800000 0x100000 0x300000; setenv bootargs $(console) $(bootargs_root); bootm 0x800000
arcNumber=3089
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
bootdelay=3
disaMvPnp=no

taked from https://archlinuxarm.org/platforms/armv5/seagate-goflex-net

cd /tmp
wget http://os.archlinuxarm.org/os/pogoplug/mke2fs
chmod +x mke2fs
./mke2fs -j /dev/sda1
mkdir alarm
mount /dev/sda1 alarm
cd alarm
wget http://os.archlinuxarm.org/os/pogoplug/bsdtar
chmod +x bsdtar
wget http://os.archlinuxarm.org/os/ArchLinuxARM-kirkwood-latest.tar.gz
./bsdtar -xpf ArchLinuxARM-kirkwood-latest.tar.gz
cd ..
umount alarm
reboot

taked from https://github.com/archlinuxarm/u-boot/wiki/GoFlex-Net

setenv baudrate '115200'
setenv bootcmd ide reset; usb start; setenv letter 9;for type in ide usb; do for disk in 0 1; do if ${type} part ${disk};then setexpr letter $letter + 1;run load;fi;done;done;'
setenv bootdelay '1'
setenv bootm 'echo Booting from ${disk} ...; run setargs; bootm ${loadaddr};'
setenv bootz 'echo Booting from ${disk} ...; run setargs; bootz ${loadaddr} - ${fdt_addr};'
setenv console 'ttyS0'
setenv ethact 'egiga0'
setenv fdt_addr '0x800000'
setenv fdt_file '/boot/dtbs/kirkwood-goflexnet.dtb'
setenv importbootenv 'echo Importing environment (uEnv.txt)...; env import -t $loadaddr $filesize'
setenv load 'echo Attempting to boot from ${type} ${disk}:1...;if run loadbootenv; then run importbootenv;fi;echo Checking if uenvcmd is set ...;if test -n $uenvcmd; then echo Running uenvcmd ...;run uenvcmd;fi;echo Running default loadzimage ...;if run loadzimage; then run loadfdt;run bootz;fi;echo Running default loaduimage ...;if run loaduimage; then run bootm;fi;'
setenv loadaddr '0x810000'
setenv loadbootenv 'load ${type} ${disk}:1 ${loadaddr} /boot/uEnv.txt'
setenv loadfdt 'load ${type} ${disk}:1 ${fdt_addr} ${fdt_file}'
setenv loaduimage 'load ${type} ${disk}:1 ${loadaddr} ${uimage}'
setenv loadzimage 'load ${type} ${disk}:1 ${loadaddr} ${zimage}'
setenv mtdids 'nand0=orion_nand'
setenv mtdparts 'mtdparts=orion_nand:1M(u-boot),-(rootfs)'
setenv setargs 'setenv bootargs console=${console},${baudrate} ${optargs} root=/dev/sd${letter}1 rw rootwait ${mtdparts}'
setenv uimage '/boot/uImage'
setenv zimage '/boot/zImage'
saveenv
reset